[已解决]ListView双击无法显示资料

jackywjl · 发表于 2011-9-26 19:57:16

本帖最后由 jackywjl 于 2011-9-27 09:43 编辑

请教各位前辈,小弟找了一些前辈们的双击资料,写了一支程式测试,结果却无法显示双击后的资料,不知哪边出了问题,源码如下~~谢谢

#include <GUIConstantsEx.au3>
#include <GUIListBox.au3>
#include <WindowsConstants.au3>
#include <GuiListView.au3>
#Include <Array.au3>
#Include <File.au3>
#Region ### START Koda GUI section ### Form=
$Form1 = GUICreate("Form1", 311, 442, 354, 130)
$Tab1 = GUICtrlCreateTab(8, 24, 289, 409)
$tab0 = GUICtrlCreateTabItem("tab1")
$ListView1 = GUICtrlCreateListView("", 8, 43, 289, 390)
_GUICtrlListView_AddColumn($ListView1, "ID", 90, 2)
_GUICtrlListView_AddColumn($ListView1, "NAME", 60, 2)
GUICtrlCreateListViewItem("1" & "|" & "2" , $ListView1)
$tab2 = GUICtrlCreateTabItem("tab2")
$ListView2 = GUICtrlCreateListView("", 8, 43, 289, 390)
_GUICtrlListView_AddColumn($ListView2, "test1", 90, 2)
_GUICtrlListView_AddColumn($ListView2, "test2", 90, 2)
GUICtrlCreateListViewItem("3" & "|" & "4" , $ListView2)
GUICtrlCreateTabItem("")
GUIRegisterMsg($WM_NOTIFY, "WM_NOTIFY")
GUISetState(@SW_SHOW)

#EndRegion ### END Koda GUI section ###

While 1
$nMsg = GUIGetMsg()
Switch $nMsg
Case $GUI_EVENT_CLOSE
Exit

EndSwitch
WEnd

Func WM_NOTIFY($hWnd, $iMsg, $iwParam, $ilParam)
      Local $hWndFrom, $iIDFrom, $iCode, $tNMHDR, $hWndListView, $tInfo ,$Menu

      $tNMHDR = DllStructCreate($tagNMHDR, $ilParam)
      $hWndFrom = DllStructGetData($tNMHDR, 2)
      $iCode = DllStructGetData($tNMHDR, 3)
      Switch $hWndFrom
            Case $ListView1
                     Switch $iCode
                              Case $NM_DBLCLK ; 响应 List1 范围内的双击
                                    $Index = _GUICtrlListView_GetSelectedIndices($ListView1)
                                    If $Index <> "" Then
                                             $L_Name = _GUICtrlListView_GetItemText($ListView1,$Index)
                                             MsgBox(0,"响应双击","你选择的是  "&$L_Name)
                                    EndIf
EndSwitch
Case $ListView2
                     Switch $iCode
                              Case $NM_DBLCLK ; 响应 List1 范围内的双击
                                    $Index = _GUICtrlListView_GetSelectedIndices($ListView2)
                                    If $Index <> "" Then
                                             $L_Name = _GUICtrlListView_GetItemText($ListView2,$Index)
                                             MsgBox(0,"响应双击","你选择的是  "&$L_Name)
                                    EndIf
                     EndSwitch
EndSwitch
      Return $GUI_RUNDEFMSG
EndFunc

haodd · 发表于 2011-9-27 02:16:07

回复 1# jackywjl

 $L_Name = _GUICtrlListView_GetItemText($ListView1,Number($Index))

$Index 换成数字型

jackywjl · 发表于 2011-9-27 09:42:23

感谢haodd大大,解决困扰我好久的问题~~感恩

damoo · 发表于 2014-4-2 20:10:45

WIN7下双击没反应，不知道怎么修改。

sak47 · 发表于 2014-10-4 09:26:40

回复 4# damoo

#PRE_UseX64=n
64位吧？注明即可

ym980616 · 发表于 2014-11-27 17:36:58

无法获取到数据吧。

rdctgvf · 发表于 2015-1-29 23:06:36

正好需要顶起

		自动登录	找回密码
密码			加入

[AU3基础] [已解决]ListView双击无法显示资料

相关帖子